- Razer deathadder 2013 gaming mouse how to#
- Razer deathadder 2013 gaming mouse update#
- Razer deathadder 2013 gaming mouse software#
- Razer deathadder 2013 gaming mouse download#
- Razer deathadder 2013 gaming mouse free#
Now, remove the scroll wheel, desolder the switches, and solder the new ones. If you can’t find them, watch the video attached below to figure that out.
When done, remove the power cable from the board’s circuit port and look for the switches that you need to replace they have Omron written on top. There are four screws that you need to unscrew to remove the board. The next thing you have to do is, remove the circuit board.
Now carefully remove the cables connected to the circuit board ports. Once you find the screws, unscrew them, and you should be able to remove the bottom plate. You can either use a magnet to find the screws and then poke with a screwdriver or remove the rubber feet and the sticker using a knife. Two screws are hidden behind the rubber feet, and the third screw is behind the product information sticker. Both Deathadder Elite and Chroma have three screws on the bottom. To replace the switches, you will have to disassemble the mouse first.
Razer deathadder 2013 gaming mouse how to#
You can take the mouse to a repair shop, and they’ll do it for you, or if you know how to solder, you can fix it yourself.
Razer deathadder 2013 gaming mouse free#
If your mouse is still in warranty, you can get a new one from Razer, free of charge, but if it’s not, you will have to replace the switches.
Razer deathadder 2013 gaming mouse download#
Step 1) Download DeathAdder 2013 or DeathAdder Chroma Updater on your Windows computer.Īs mentioned before, if you cannot fix the problem by following the methods mentioned in this guide, the mouse’s Omron switches need to be replaced. Note: We only found DeathAdder 2013 and Chroma’s firmware updater if you are facing the double click issue on Elite or any other model, try contacting Razer Support.
Razer deathadder 2013 gaming mouse update#
After the double click issue was first recognized, Razer had advised the people who were facing the issue to update the mouse’s firmware.
Razer deathadder 2013 gaming mouse software#
Gaming mouse firmware is a software program just like the firmware of other devices like smartphones, it provides important instructions to the mouse. Before you try this method, keep in mind that you may have to breathe air from different angles and do it 4-5 times. There are antistatic sprays available in the market, but it’s better to blow humid air or breath into the gap gently. Some people breathe into the gap and think it got fixed because there was dirt on the switches, but in reality, the humidity present in the breath helps in removing the static charge buildup. To release the charge, you can blow humid air or gently breath into the gap between the button and the mouse. Sometimes mouse switches get a static charge buildup that can cause the double click issue. Method 2) Release the Static Charge Buildup
This will reset the mouse and hopefully fix the double-click issue. Step 4) After 5 – 10 seconds, release the buttons. Step 3) While holding down the mouse buttons, connect the mouse to the computer. Step 2) Press and hold down the Right + Left Mouse Button + Scroll Wheel. Step 1) Disconnect the mouse from the computer. Before you jump to the next section and start following the steps mentioned below the methods, keep in mind, trying just one method may not work if so, we recommend trying all of them until one of them fixes the issue. We have tried to cover all the methods which usually fix the double click problem on Razer mice. Methods to Fix Razer Deathadder Double Click Issue? Below we have mentioned some methods to fix the problem trying all of them one by one will hopefully fix the problem. In some rare cases, faulty mouse switches can also cause the double click issue. Multiple reasons can cause the double click issue, the most common is software related, but sometimes static charge buildup can be the reason. This article explains why this problem occurs with Razer mice and how you can fix it by using one of the methods we have covered. The double-clicking issue with Razer mice was first reported years ago, the number of instances may have reduced after Razer addressed the issue and fixed it in a firmware update, but still, it remains a big problem for those who use mice like DeathAdder, 2013, Elite, V2, Chroma, and even Razer Naga. When you buy through links on our site, we may earn an affiliate commission.
0 kommentar(er)
